Skip Navigation

BOEING

Boeing Job Description Boeing Job Description
Search

Search Jobs

Browse By Category

Browse By Location

Browse by Category & Location

Special Projects Mech B

Company The Boeing Company Job ID 1900034056 Date posted 02/19/2019
Location Tukwila Washington United States
Job Description

Boeing is the world's largest aerospace company and leading manufacturer of commercial airplanes and defense, space and security systems. We are engineers and technicians. Skilled scientists and thinkers. Bold innovators and dreamers. Join us and you can build something better for yourself, for our customers and for the world.

 

Position Description: 

 

Assist, instruct and work with mechanics in various sub and final assembly shops, to assemble and install parts, structural components and sub-assemblies on special project airframes, including aircraft and space vehicles. These sub-assemblies are typically installed on the final assembly at various locations. Employment in this position also requires twisting at the waist, use of low impact vibratory tools, walking, standing, carrying/lifting, rotation of head/neck, contact with metals, plastics, solvents, exposure to noise, and the use of personal safety gear for hand/arms, eyes and ears.

 

Duties and Responsibilities:

  

Obtain and verify kitted (pre-picked) detail parts, standards, and assemblies were issued correctly by comparing part numbers and quantities to drawing(s).

 

Ensure that parts issued are effective for the airplane and are free of visible defects. Locate parts on assembly tools, mating parts and/or assemblies per drawing.

 

Align parts to tool stops, matching pilot holes or by hand layout and secure in place using Clecos or tooling/hand clamps.

 

Check for good edge margins and alignment. Shim parts as required per drawing.

 

Drill, ream, countersink full size holes in parts and or assemblies, in proper sequence and to correct size, using a drill motor (e.g., Winslow, 90-degree power vane, or quackenbush) per drawing.

 

Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners.

 

Use solvents to clean surfaces prior to sealing or assembly. Apply sealant, (e.g., Moldable Plastics Shim (MPS)), alodine, primer, adhesives and special finishes.

 

Install fasteners (e.g., Eddie bolt, hi-lock) in correct sequence per drawing, using correct tools (e.g., Eddie ratchet wrench, rivet gun and bucking bar, c-squeeze, nut runner). Locate and install fuel, hydraulic, high pressure compressed gas lines, wire bundles into assemblies per drawing. Install bushings into housings using arbor press and/or hydraulic puller.

 

Apply liquid nitrogen to facilitate installation of bushings. Roller/anvil swage or ball stake bearings and bushings into machined housings per drawing.

 

Clean parts and identify by applying part marking. Check work after completion of each operation in job and/or completed job to ensure it is complete and there are no defects (e.g., gapped heads, high rivets, tool mark, incorrect length fasteners).

 

Operate mechanical lifts of various types (e.g., scissor and snorkel lifts), to locate parts/assemblies into position or to perform assembly work. Move parts and/or assemblies using overhead cranes, stackers and pallet jacks.

 

Clean work area and assemblies to ensure that all Foreign Object Debris (FOD) has been removed. Submit completed job or in-process checks to inspector at appropriate steps in sequence, using an electronic call sheet.

 

Perform minor rework as required (e.g., pick ups, NCO (Non Conformance Order). Assist higher graded employees performing testing/installation (e.g., mechanical, electrical, ordnance).

 

Handle and dispose of hazardous materials in approved manner.

 
 

Boeing is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national origin, gender, sexual orientation, gender identity, age, physical or mental disability, genetic factors, military/veteran status or other characteristics protected by law.

 


Division
Fabrication

Relocation Assistance Available
No. Relocation assistance is not a negotiable benefit.

Qualifications

BASIC QUALIFICATION QUESTIONS:

 

Frequent use of personal protective equipment for face/eyes and occasional use of hand/arm and ear protection may be required. Must be able to obtain and maintain personnel certifications as required to support job responsibilities.

 

Occasional contact with Metals, exposure to plastics and solvents and exposure to Atmospheric Conditions

 

Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will be considered as this job is not installed in QTTP.

 

This is an hourly position governed by the IAM Collective Bargaining agreement.

This position requires occasional (1-3 Hrs) Finger manipulation, Flexion/Extension, Handling, Lifting less than 25 pounds, Carrying less than 10 lbs, Rotation of head/neck, Sitting, Standing, and Walking.

 

High school graduate or GED preferred.

 

Experience in manufacturing, composites, fabrication, or assembly processes

 

Experience in a manufacturing or assembly environment

 
"This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R.  § 120.15 is required.  "US Person" includes US Citizen, lawful permanent resident, refugee, or asylee."

 

 

 

 


Experience Level
Individual Contributor

Job Type
Standard

Travel
No

Contingent Upon Program Award
No

Union
Yes

Job Code
98206

Related Jobs

EEO is the Law

Boeing supports equality and diversity.

Download the EEO is the Law Poster (PDF Link).

Learn more about Accessibility

Accessibility

If you need a reasonable accommodation for any part of the employment process, please contact us.

Learn More

Computer generated silouette of a person

My Account

Create an account, update your information, or check the status of your application.

Log In or Create Account